|
DEFENDER SAFETY SYSTEM®
ENERGY SAVER MODELS AND NON-DEFENDER MODELS
 These conventional (atmospheric) vent water heaters
are the time-tested workhorses of water heaters. Unlimited flow rates and large stand-by supplies of hot water make this design
the most popular style across a wide geographic area. 75 and 100-gallon models do not include Defender Safety System®.
(Sample model numbers include: M-I-303T6FBN, M-I-40T6FBN, M-I-5036FBN - Non-Defender Energy Saver model numbers
include: M-I-75S6BN & M-I-100T6BN)
Defender Safety System Features
- Advanced ScreenLok® Technology Flame Arrestor design
- Resettable thermal switch
- Piezo ingiter
- Maintenance
free
- Pedestal base
- Sight window
Standard Energy Saver features
- Fully automatic controls
- Factory installed Hydrojet® Total Performance System
- Vitraglas® lining
- Factory installed dielectric waterway fittings
- Protective magnesium anode rod
- "3" x "4" Snap-Lock draft diverter on 40,000 BTU/Hr. or less models
- T&P relief valve included
- Brass drain valve
- 1" Non-CFC foam insulation (except where noted)
DEFENDER SAFETY SYSTEM® ENERGY SAVER (XR) MODELS AND NON-DEFENDER MODELS
CLICK HERE FOR INFORMATION ON DEFENDER SAFETY SYSTEM®
 These conventional (atmospheric) vent water heaters
offer “Extra Recovery” (XR) which translates to an increased amount of hot water available at a usable temperature
in less time than normal. 75-gallon model does not include Defender Safety System®.
(Sample model numbers
include: M-1-XR403S6FBN, M-2-XR504T6FBN, M-2-XR65T6FBN - Non-Defender XR model numbers include: M-2-XR75S6BN)
Defender
Safety System features
- Advanced
ScreenLok® Technology Flame Arrestor design
- Resettable thermal switch
- Piezo
ingiter
- Maintenance free
- Pedestal base
- Sight window
Standard Energy Saver features
- Fully automatic controls
- Factory Installed Hydrojet® Total Performance System
- Vitraglas® lining
- Factory installed dielectric waterway fittings
- Protective magnesium anode rod
- ¾" Side Connections for space heating
- Snap-lock draft diverter
- T & P relief valve included
- Brass drain valve
- 2"
Non-CFC foam insulation (1" on M1 models)
TTW®1 MODELS
 Our basic through-the-wall power-vented model, the
TTW®1 can be vented vertically or horizontally directly through the nearest outside wall.
(Model numbers include:
M-1-TW-40S6BN & M-1-TW-50S6BN)
- Intermittent
Pilot Ignition System - no standing pilot
- Can
be vented both horizontally and vertically
- May
be installed up to 30' from outside wall with 2" PVC vent pipe and 3 elbows
- May be installed up to 90' from outside wall with 3" PVC vent pipe and 3 elbows
- Agency approved for use with schedule
40 ABS, schedule 40 PVC and schedule 40 CPVC
- Power vented for positive exhaust
- Vitraglas® lining
- Protective
magnesium anode rod
- Factory installed
dielectric waterway fittings
- Factory
installed Hydrojet® Total Performance System
- Smart Valve control
- T&P
relief valve opening on side of tank
- Smart
Valve control
- Slider Combustion
Chamber Door
- T&P relief valve
opening on side of tank
- Brass
Drain Valve
- Slider Combustion
Chamber Door
- Brass Drain Valve
- 1" Non-CFC foam insulation
TTW®2 MODELS
 Similar to our TTW®1 models, the TTW®2 offers
higher BTU inputs, two inches of insulation and an 80% recovery efficiency. Just like the TTW®1, the TTW®2 offers
extremely flexible venting options.
(Sample model numbers include: M-2-TW-50T6BN & M-II-TW-75T6BN)
- Intermittent Pilot Ignition System - no standing pilot
- Can be vented both horizontally and vertically
- May be installed up to 30' from
outside wall with 2" PVC vent pipe and 3 elbows
- May be installed up to 90' from outside wall with 3" PVC vent pipe and 3 elbows
- Agency approved for use with schedule 40 ABS, schedule 40 PVC and
schedule 40 CPVC
- Power vented
for positive exhaust
- Vitraglas®
lining
- Protective magnesium anode
rod
- Factory installed dielectric
waterway fittings
- Factory installed
Hydrojet® Total Performance System
- Smart
Valve control
- T&P relief
valve opening on side of tank
- Slider
Combustion Chamber Door
- Brass
Drain Valve
- 2" Non-CFC foam
insulation
|
|
|
