Trusted Heating and Cooling, Electrical & Water Heater Services in Milford, MI

Completed routine cooling system maintenance inspection per Worry Free Service Agreement. Inspected condensate drain assembly and verified proper drainage function, checked air return grille for adequate airflow and proper operation. All system components found operating within normal parameters with no issues identified.

Installed a new Bradford White 40-gallon atmospheric vent natural gas water heater, model RG240T6N, with 40,000 BTU/hr input rating. The unit was positioned in a utility closet alongside existing HVAC equipment, with proper clearances maintained per manufacturer specifications and code requirements. All gas connections, water supply lines, temperature and pressure relief valve, and venting were completed to ensure safe and efficient operation of the new water heating system.

Completed comprehensive AC tune-up on approximately 15-year-old outdoor condensing unit. Performed system diagnostics using Fieldpiece SMAN manifold gauge, measuring refrigerant pressures and temperatures across the system to verify proper charge levels and operational parameters. Inspected condenser coils, fan operation, electrical connections, and refrigerant lines; noted unit operational with readings within acceptable range for ambient conditions.

Completed comprehensive tune-up and maintenance on 21-year-old outdoor air conditioning unit located in backyard brick enclosure. Performed standard preventive maintenance procedures including coil cleaning, which generated foam residue visible around unit base on concrete pad. Inspected internal components including evaporator coils, motor assembly, drain pan, and electrical connections; noted age-related discoloration on coil surfaces but system operational. Unit protected by wire cage guard and functioning within normal parameters with no reported issues prior to service.

Completed estimate for water heater replacement in residential utility space. Evaluated existing water heater system with gray storage tank, blue pressure tank, copper supply lines, and metal venting configuration. Assessed current plumbing connections including brass fittings and shutoff valves. Documented equipment specifications and mechanical room layout to provide replacement options and pricing for new water heater installation.

Responded to no-start condition on Millvank 12kW generator displaying fault codes FC3 and FC4. Upon inspection, identified failed run capacitors in the electrical panel showing visible aging and discoloration. Replaced both capacitors, verified all electrical connections and wire terminations, cleared fault codes, and successfully tested unit operation to confirm proper startup and running performance.

Completed scheduled maintenance on Kohler generator unit. Performed comprehensive inspection of electrical and mechanical components, including testing of dual run capacitors which were found to require replacement. Removed and replaced failed capacitors, verified proper operation of control board with indicator lights functioning normally, and conducted full system operational test to confirm generator performance and readiness.

Completed scheduled cooling maintenance on Bryant 595DBA outdoor condensing unit as part of Worry Free Service Agreement. Performed comprehensive system inspection, verified proper operation of all components, and documented unit condition with exterior showing good maintenance status and no visible deterioration or damage requiring immediate attention.

Responded to expedited no-cool call on nine-year-old air conditioning system with reported repeat failure after recent capacitor replacement. Upon arrival, accessed outdoor disconnect panel and performed electrical diagnostics using digital multimeter. Verified voltage readings at 242V and inspected all electrical connections, circuit breakers, and wiring integrity at the disconnect box. Examined capacitor that was previously replaced one to two months prior to determine if repeat failure had occurred. Conducted comprehensive system evaluation to identify root cause of cooling loss affecting entire home. All electrical components at disconnect panel tested and inspected, connections secured, and system functionality restored to ensure reliable operation for household with medical necessity.

Conducted comprehensive assessment of existing HVAC system in basement installation, including furnace unit and associated ductwork. Unit confirmed to be over 10 years old with suspected clogging issues. Documented current equipment configuration, including copper refrigerant lines, PVC condensate drainage system, metallic ductwork, and furnace cabinet with filter access panel. Photographed complete installation layout for estimate preparation and replacement recommendation.

Completed annual AC tune-up on 4-year-old outdoor condensing unit. Performed comprehensive system inspection including visual assessment of condenser coil, refrigerant lines, electrical connections, and disconnect box. Documented equipment condition with photos showing unit positioned on pad with proper clearance, copper line connections intact, and electrical components secure. System operating within normal parameters for seasonal maintenance visit.

Completed comprehensive heating maintenance on residential HVAC system including furnace and air handler unit. Cleared thermostat alerts as requested, performed full system inspection of electrical components, control board, blower motor assembly, and verified proper operation of all safety controls. All equipment found in good working condition with no issues identified.

Completed full HVAC system replacement including installation of Lennox 80% efficiency gas furnace, new central air conditioning unit, and T6 programmable thermostat for improved climate control and energy management. Installed 50-gallon residential water heater with new chimney liner to ensure proper venting and code compliance. Added electrical disconnect box with fused switches for AC unit, wired with appropriate 240V service including hot conductors, neutral, and ground connections, and installed exterior junction box with properly secured wire connections and strain relief fittings mounted to building exterior. Configured system for interruptible service capability as requested, completing all electrical connections with code-compliant wire nuts and cable management.

Completed preventive maintenance on two Carrier air conditioning systems. Performed comprehensive inspection of outdoor condenser units, including examination of condenser coils, fins, and heat exchanger components. All units found in satisfactory operating condition with coils clean and fins properly aligned for optimal airflow and heat transfer efficiency.

Completed scheduled maintenance on residential air conditioning system. Performed comprehensive inspection of outdoor condensing unit and indoor air handler components, including compressor, condenser coils, evaporator fan assembly, and refrigerant lines. All components found operating within normal parameters with no issues identified during inspection.

Completed scheduled cooling season preventive maintenance on residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, noting weathered coil fins with debris accumulation and vertical staining patterns indicating extended outdoor exposure, minor corrosion present at base cabinet junction. Inspected indoor evaporator coil assembly and condensate drain pan, observed staining and mineral deposits consistent with normal system operation. Verified refrigerant lines, electrical connections, and drainage components. System operational within normal parameters upon completion of maintenance service.

Responded to service call for reported water heater leak. Upon arrival, performed thorough inspection of Rheem Professional series tanked water heater unit and surrounding plumbing connections. Examined all visible components including copper supply lines, brass fittings, temperature and pressure relief valve, drain valve, and tank exterior for signs of moisture or active leaking. Inspected overhead ductwork connections and exhaust vent pipe for proper installation and clearances. Documented equipment condition with photographs showing water heater installation, blue water treatment filter system, and associated mechanical room plumbing infrastructure. Verified warranty status and provided assessment findings for next steps.

Performed scheduled maintenance on residential Vanguard 627cc standby generator unit. Inspected and replaced worn spark plugs showing carbon deposits and electrode wear. Verified all electrical connections, control box wiring, and mounting hardware for proper operation and security.

Performed comprehensive electrical assessment for generator installation at residential property. Evaluated existing electrical infrastructure including main service panel located in attic space and exterior meter configuration serving multiple units. Documented current electrical panel capacity, breaker arrangement, and available circuits in Westinghouse load center to determine compatibility with proposed generator system. Assessed exterior meter bank installation consisting of two digital smart meters and one DTS meter with associated conduit runs to identify proper connection point for generator transfer equipment. Captured detailed photographic documentation of panel interior showing circuit breaker layout and available spaces, as well as exterior service entrance configuration including PVC and metallic conduit routing for preparation of formal generator installation estimate.

Successfully installed a 50-gallon Bradford White tanked water heater in the basement utility area. The installation included proper copper pipe connections at the base of the unit, integration with existing plumbing infrastructure, and appropriate venting with aluminum flexible ductwork featuring secure connections and proper sealing at elbow joints. The water heater was positioned to allow adequate clearance for maintenance access while coordinating with existing HVAC equipment, including the Bryant furnace, blue expansion tank, and associated PVC piping systems throughout the mechanical room.