Trusted Heating & AC Services in Royal Oak, MI

Completed full boiler installation in basement utility area, including mounting and connection of new heating unit with integrated expansion tank and copper piping distribution system. Installed two zone circulator pumps at base of unit for hydronic heating control, along with two thermostats and system controller with proper wiring to green control panel. Established all mechanical and electrical connections per code requirements, utilizing braided flex connectors and rigid copper piping with professional fittings throughout the system. Secured mechanical and electrical permits prior to installation and reconnected all heating zones to ensure proper system operation and zoning capability.

Completed installation of Lennox furnace system in basement utility room, including proper mounting of air handler unit against prepared wall surface. Installed condensate drainage system with white PVC piping routed vertically through interior space and exterior wall, terminating with appropriate elbow fitting on building exterior, and connected condensate pump with dedicated electrical supply to ensure proper moisture removal from system.

Completed free estimate for replacement of 25-year-old furnace located in basement and 25-year-old central air conditioning unit located outside. Photographed existing equipment including basement furnace with adjacent water heater and outdoor condenser unit with heavily rusted fan guard and weathered copper refrigerant lines. Customer also requested separate estimate for water heater replacement to be scheduled as plumbing service at later date.

Completed scheduled maintenance on air handling unit. Replaced heavily soiled air filter that was completely clogged with dust and debris, restricting airflow to the system. Installed new evaporator pad and filter to restore proper ventilation and system efficiency.

Conducted furnace inspection and identified cracked heat exchanger in Tempstar unit requiring immediate attention due to safety concerns. Documented existing HVAC system configuration including furnace, air handler with Lasko blower motor, ductwork, and associated plumbing connections, and prepared replacement estimate for homeowner review. Also provided repair estimate as requested for comparison of options.

Responded to no heat call with reported melted insulation on furnace in basement. Upon arrival, found furnace had been shut off as a safety precaution. Inspected unit and wiring compartment, documenting condition with photos showing multiple wire runs, conduit routing, and general cabinet interior. Assessed electrical connections, wiring integrity, and component condition to determine cause of insulation damage and verify safe operation before restoring heat to occupied unit.

Responded to service call for inoperative Generac generator system approximately 2 years old and covered under 10-year manufacturer warranty. Upon arrival, located exterior-mounted Generac automatic transfer switch on building exterior wall with multiple conduits and connections. Performed visual inspection of transfer switch enclosure and noted significant vegetation overgrowth around unit requiring clearance for proper access and ventilation. Documented current installation conditions with photographs showing transfer switch mounting, conduit routing, and surrounding environment. Verified warranty coverage status and reviewed service eligibility with customer regarding dispatch fees and warranty terms. Assessed transfer switch operation and electrical connections to diagnose cause of generator failure to start or transfer load during power outage conditions.

Responded to furnace service call for cracked heat exchanger evaluation. Performed thorough inspection of existing HVAC system and documented failed heat exchanger component requiring immediate attention due to safety concerns. Provided comprehensive replacement estimate for new furnace system installation, including equipment specifications and scope of work required to restore safe heating operation to the property.

Completed comprehensive plumbing and HVAC system modifications in basement utility area. Reworked entire drain system, connecting into existing 2" PVC line with proper pitch and securing. Corrected furnace and water heater venting configuration using appropriate metallic ductwork and fittings to ensure safe exhaust operation. Removed existing humidifier unit from system. Installed replacement motor for HVAC equipment. All work performed to code with proper pipe supports and duct connections verified for functionality.

Completed furnace and air conditioning maintenance on residential HVAC system. Performed comprehensive inspection of outdoor condenser unit, including examination of compressor, refrigerant lines, electrical connections, and fan assembly. Customer enrolled in Worry Free Service Agreement for ongoing preventative maintenance coverage.

Completed preventive maintenance on residential air conditioning system. Inspected outdoor condenser unit, verified proper operation of condenser fan and protective grille assembly, and checked indoor air handler components. Examined condensate drain pan and pump assembly, confirmed proper drainage function with active condensation present, and noted normal moisture accumulation with minor mineral deposits on drain pan surface.

Conducted comprehensive electrical site assessment for backup generator installation. Photographed and documented existing 200-amp main electrical panel configuration, including current circuit breaker layout and all labeled circuits serving critical loads such as HVAC system, hot water heater, furnace, and various branch circuits throughout the residence. Evaluated panel capacity and available breaker spaces to determine optimal integration point for automatic transfer switch. Documented existing circuit identification labels to assess essential circuits requiring backup power during utility outages. Inspection confirmed panel accessibility and adequate clearance for generator tie-in work in unfinished utility area.

Performed scheduled maintenance on residential standby generator system. Removed and inspected spark plugs, finding normal wear consistent with operating hours. Verified all safety labels and warning placards intact and legible on unit housing. Inspected control panel display for proper function, confirming digital readout operational and system parameters within normal range. Examined electrical connections and wiring for signs of wear or damage, finding all connections secure. Documented equipment serial number and model information for service records. Unit tested and returned to operational status with all systems functioning as designed.

Conducted comprehensive assessment of 20+ year old non-operational air conditioning system located in backyard and natural gas furnace in basement utility area. Evaluated existing outdoor condenser unit with vertical coil component and indoor furnace with associated ductwork and PVC venting system. Provided replacement estimate for complete HVAC system upgrade to restore cooling and heating functionality.

Conducted on-site evaluation for new whole home generator installation at manufactured home. Assessed existing electrical infrastructure including main service panel located in basement utility area and evaluated copper plumbing lines in proximity to proposed installation area. Documented current electrical panel configuration with dual-column breaker arrangement to determine capacity and integration requirements for generator transfer switch. Evaluated basement access points, utility routing pathways, and structural considerations for equipment placement and necessary electrical connections. Provided comprehensive estimate for whole home generator system installation including equipment specifications, transfer switch requirements, and necessary electrical modifications to existing service panel.

Completed scheduled AC maintenance tune-up under prepaid maintenance plan on outdoor condensing unit. Performed comprehensive system inspection including examination of condenser coil, fan motor assembly, electrical connections, refrigerant lines, and control components. All components found operating within normal parameters with no deficiencies noted during inspection.

Completed call-back service to address code violations identified during initial 40-gallon natural draft water heater installation. Installed combustion air openings to furnace/water heater room per code requirements, providing one square inch per 1000 BTU input of appliances with high opening at ceiling level and low opening at floor level. Secured water heater draft diverter with four screws per manufacturer specifications to ensure proper venting operation and code compliance.

Provided estimate for air conditioning system replacement of aging outdoor condensing unit that is not performing adequately following recent service call for humidity issues. Evaluated existing equipment condition, site installation requirements, and discussed replacement options with service credit applied toward new system installation.

Completed scheduled Air Care Maintenance on residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, including cleaning of coils and removal of debris accumulation from louver sections. Verified proper operation of condenser fan, checked refrigerant levels, and confirmed unit functionality. System operating within normal parameters upon completion of preventive maintenance service.

Completed scheduled AC maintenance on outdoor condensing unit. Performed comprehensive 10-point inspection including examination of compressor, refrigerant lines, condenser coil, electrical connections, and all system components. Unit found in operational condition with minor dust accumulation on condenser fins, which is normal for seasonal operation.